mk1-forum.net

very late MK2 . Nice project

mk2 project
http://www.ebay.co.uk/itm/austin-mini-m ... OSwgmJX0Fr~

seller seems familiar

I don't believe it!

Rich is actually having a clear out!

You would almost think he had something that needed paying for

You could always put it on ebay mate.

On a separate note, that MK2 shell is extraordinarily straight & would make a good all be it basic basis of a superb shell one the restoration work was done.

I will make it fit, I WILL MAKE IT FIT!

Possibly not the most elegant fitting solution ever offered for a LL wheel.

mk1 wrote:I will make it fit, I WILL MAKE IT FIT!

Possibly not the most elegant fitting solution ever offered for a LL wheel.

Interesting to see a Cambridge horn push used - I did look at that option but the boss it mounts on needs to sit at least 23mm off the steering wheel to enable the sprung centre contact to do it's job and as you say ends up looking rather incongruous. Might not look so bad with a deeper dished wheel but the rim would then end up right under your nose...

My 'fag packet' notes are here : http://i872.photobucket.com/albums/ab28 ... kfo8ru.jpg

Nick W wrote:mk2 project
http://www.ebay.co.uk/itm/austin-mini-m ... OSwgmJX0Fr~

seller seems familiar

yeah

I'm having a clear out

the roof on my tent has ripped and I just cannot be arsed paying for another one, so everything that is in there is going to have to go

this is the remains of the old 'stinky pete' that was found in that garage in Harrogate

I'm afraid to say that ive been robbing bits and bobs off it for other cars over the years


I have made a mistake putting it on ebay at a 99p start, 40 plus people have 'wotz ur best price pal' etc so far - arrgg


its going to be at minispares north from next Monday on (emergency storage.... )

so I will say that as a special to any member on here

bid a decent, fair price and as long as you can collect it from next Monday - Saturday, within work hours I will accept

my ebay mojo is running out already............................


got loads and loads more stuff, cars, etc are going to be up for sale

having a serious thin out (of minis)

Oselli Rocker Cover
http://www.ebay.co.uk/itm/CLASSIC-MINI- ... SwFV9X0uMA

"Don't come up for sale often"

Yet still being made by Oselli

I'm Ebaying an Oselli tuning kit soon, carbs/manifold/cylinder head/rocker cover. Are the new covers the same as the old ones?

No there not Pete. If I'm right, the old ones are Alloy and the new ones are cast.

Good!

These are expensive but original BMC/BL parts,
Cable door pulls:
http://page10.auctions.yahoo.co.jp/jp/a ... m163624325

Lever door pulls:
http://page2.auctions.yahoo.co.jp/jp/auction/b223586839

Moustache ends:
http://page24.auctions.yahoo.co.jp/jp/a ... q110700157

Also on the block,
Early aluminum sill and cross member covers, seen better days:
http://page6.auctions.yahoo.co.jp/jp/auction/f188724664

Grey/grey rear seat covers, don't look horrendous, apart from being dirty they do not appear to have any rips:
http://page16.auctions.yahoo.co.jp/jp/a ... u115483886

tjw89 wrote:"Don't come up for sale often"

Yet still being made by Oselli

How much from Oselli?
Seller has now relisted at even higher BIN price......
http://www.ebay.co.uk/itm/CLASSIC-MINI- ... 2244904911

£175+VAT, so £210 inc VAT

http://www.oselli.com/classic_oselli/services/midget

350 for a Donwton badge http://www.ebay.com/itm/182277632548?ul_noapp=true

zbarbera wrote:350 for a Donwton badge http://www.ebay.com/itm/182277632548?ul_noapp=true

why don't you just pay 25 quid for one from downton?

I did

Me too, but now I have two n.o.s. originals found on the Beaulieu Auto Jumble

Kees.

Broadspeed GT ?

http://www.ebay.co.uk/itm/Hillman-Minx- ... Sw9NdXu0IH

Kees.