Front Cam Bearing Change
- gs.davies
- Site Admin
- Posts: 1641
- Joined: Fri Oct 26, 2012 2:29 pm
- Location: Essex, UK
- Has thanked: 19 times
- Been thanked: 34 times
- Contact:
Front Cam Bearing Change
Has anyone successfully removed and installed a new front cam bearing while the engine and box are still attached?
- Peter Laidler
- 1275 Cooper S
- Posts: 6162
- Joined: Sat Jul 15, 2017 5:35 pm
- Location: Abingdon Oxfordshire
- Has thanked: 34 times
- Been thanked: 34 times
Re: Front Cam Bearing Change
Ah, Gary....... No doubt there will be some bright soul on the forum that says that it CAN be done and indeed, he's done it. But somehow, I bet that in doing so, engine in-situ, it becomes one of those jobs, several hours in and bits spread all over the garage floor, you'll be thinking to yourself that '......it would have taken half the time if I'd just taken the whole bloody thing out to start with. AND done a few other jobs at the same time.
Been there and done it many times.......
Been there and done it many times.......
- gs.davies
- Site Admin
- Posts: 1641
- Joined: Fri Oct 26, 2012 2:29 pm
- Location: Essex, UK
- Has thanked: 19 times
- Been thanked: 34 times
- Contact:
Re: Front Cam Bearing Change
I'm not considering doing with the engine in the car, rather trying to avoid having to split the engine and box whilst it's on the floor.
- Peter Laidler
- 1275 Cooper S
- Posts: 6162
- Joined: Sat Jul 15, 2017 5:35 pm
- Location: Abingdon Oxfordshire
- Has thanked: 34 times
- Been thanked: 34 times
- timmy201
- 1275 Cooper S
- Posts: 1925
- Joined: Mon Jun 10, 2013 9:57 am
- Location: Australia
- Been thanked: 5 times
Re: Front Cam Bearing Change
I guess theoretically it would be possible, but you'd want to try and remove the cam bearing outwards with a slide hammer rather than pushing it in like normal. You'd also need to be careful not to introduce any swarf into the sump
-
- 1275 Cooper S
- Posts: 2818
- Joined: Fri Jan 15, 2016 12:22 pm
- Location: Silverstone not far away
- Has thanked: 6 times
- Been thanked: 22 times
Re: Front Cam Bearing Change
Remember Past Forum topic .. problem engine running where Engine Oil was filling up in the Rocker Cover & not draining ..the cause was an installing the wrong way around front cam bearing.
- gs.davies
- Site Admin
- Posts: 1641
- Joined: Fri Oct 26, 2012 2:29 pm
- Location: Essex, UK
- Has thanked: 19 times
- Been thanked: 34 times
- Contact:
Re: Front Cam Bearing Change
Yes, that’s the problem.
Hoping for a quick fix to this that doesn’t involve a complete strip down of the engine.
Hoping for a quick fix to this that doesn’t involve a complete strip down of the engine.
Re: Front Cam Bearing Change
I'm certain that the appropriately sized blind bearing puller and slide hammer would get the job done cleanly.
-
- 1275 Cooper S
- Posts: 2818
- Joined: Fri Jan 15, 2016 12:22 pm
- Location: Silverstone not far away
- Has thanked: 6 times
- Been thanked: 22 times
Re: Front Cam Bearing Change
i would be concerned as to how to get the Cam refitted without causing unseen damage to the Camshaft as getting the Cam through the bearings is always a job that needs care ..let alone how to connect the Cam onto the installed Oil Pump drive that would be a challenge.. then how would you know the Cam spun freely when it was re-fitted.
the Long way is probably the best way to resolve the problem.
the Long way is probably the best way to resolve the problem.
- Exminiman
- 1275 Cooper S
- Posts: 2954
- Joined: Tue Jan 17, 2017 7:59 am
- Location: Berkshire UK
- Has thanked: 24 times
- Been thanked: 16 times
Re: Front Cam Bearing Change
Agree with the above comments, you can probably pull the old one out and drive another one in........
But how will you know if the cam is free running or if the oil way in the bearing is properly lined up, or whether the bearings need a scrape etc....honestly, I would not try it, just because of the potential fall out.
This is quite a good vid to illustrate issues, especially dropping (rather than sliding in) the cam in and grinding out the oil hole in bearing
https://youtu.be/eZM_4owPcpQ
But how will you know if the cam is free running or if the oil way in the bearing is properly lined up, or whether the bearings need a scrape etc....honestly, I would not try it, just because of the potential fall out.
This is quite a good vid to illustrate issues, especially dropping (rather than sliding in) the cam in and grinding out the oil hole in bearing
https://youtu.be/eZM_4owPcpQ
-
- 1275 Cooper S
- Posts: 1269
- Joined: Thu Jun 24, 2010 11:55 pm
- Location: Tasmania, Australia
- Has thanked: 4 times
- Been thanked: 8 times
Re: Front Cam Bearing Change
I'm not sure what block you have, but if its a 1300 without tappet covers, you would need to take some sort of preventative measures to hold back the cam followers so you can firstly pull the camshaft out, and then so that they don't fall down into the gearbox. Maybe stand the whole lot on end so that they are horizontal?
Also the cam bearings are meant to be line-reamed after fitting. I'm not sure how critical it is.
Tim
Also the cam bearings are meant to be line-reamed after fitting. I'm not sure how critical it is.
Tim
1951 Morris Commercial J Type Van
1955 BSA C11G
1961 Morris Mini Traveller
1969 Triumph TR6R
1977 Leyland Moke Californian
1955 BSA C11G
1961 Morris Mini Traveller
1969 Triumph TR6R
1977 Leyland Moke Californian
- MiNiKiN
- 1275 Cooper S
- Posts: 951
- Joined: Tue Oct 10, 2017 3:15 pm
- Location: Graz/Austria // NN1 4ST previously
- Has thanked: 20 times
- Been thanked: 10 times
Re: Front Cam Bearing Change
Or as I tend to say: "How am I supposed to know what I think, before I hear what I say?"Peter Laidler wrote: ↑Fri Oct 18, 2024 2:39 pm Ah, yes..... Understand now! Opened mouth before engaging brain
Yes I am a nerd: I am researching the Austrian Mini-racing scene of the 60s and 70s